Leading source of IT Certification Training – Latest Pass4itsure VCE Exam Simulator, VCE to PDF, A+ VCE

Work hard! It’s not hard to get certified! Share the latest Cisco CCNA 200-125 exam dump for free. online 200-125 exam practice tests. the latest 200-125 exam questions and answers, and guarantee your skills and exam experience! “Cisco Certified Network Associate Exam (CCNA)” – 200-125 exam! pass4itsure.com expert recommendation! Top pass rate!

image from: https://www.toolshero.com/psychology/personal-happiness/principles-of-success/

Get the latest Cisco CCNA 200-125 pdf

[PDF] Free Cisco 200-125 pdf dumps download from Google Drive: https://drive.google.com/open?id=1syr8vW4wXaGVsbZuZze8ax2W3KUyIAIt

[PDF] Free Full Cisco pdf dumps download from Google Drive: https://drive.google.com/open?id=1xM4qOTLaMDVyi16Ta0wO8qvdS21TfgOU

Valid information provided by Cisco officials

200-125 CCNA – Cisco: https://www.cisco.com/c/en/us/training-events/training-certifications/exams/current-list/200-125-ccna.html

The latest Cisco CCNA 200-125 exam practice questions test your strength

QUESTION 1

What is the most efficient subnet mask for a point to point ipv6 connection? 

A. /127 

B. /128 

C. /64 

D. /48 

E. /32 

Correct Answer: A 

Explanation: ref : https://tools.ietf.org/html/rfc6164 

QUESTION 2

Which command can you enter to configure a local username with an encrypted password and EXEC mode user

privileges? 

A. Router(config)#username jdone privilege 1 password 7 08314D5D1A48 

B. Router(config)#username jdone privilege 1 password 7 PASSWORD1 

C. Router(config)#username jdone privilege 15 password 0 08314D5D1A48 

D. Router(config)#username jdone privilege 15 password 0 PASSWORD1 

Correct Answer: A 

QUESTION 3

Which two statements about static NAT translations are true? (Choose two.) 

A. They allow connections to be initiated from the outside. 

B. They require no inside or outside interface markings because addresses are statically defined. 

C. They are always present in the NAT table. 

D. They can be configured with access lists, to allow two or more connections to be initiated from the outside. 

Correct Answer: AC 

Static NAT is to map a single outside IP address to a single inside IP address. This is typically done to allow incoming

connections from the outside (Internet) to the inside. Since these are static, they are always present in the NAT table

even if they are not actively in use. 

QUESTION 4

Between which two states does a port transition when PortFast is enabled? (Choose two) 

A. blocking 

B. forwarding 

C. active 

D. listening 

E. learning 

Correct Answer: AB 

QUESTION 5

What is the default administrative distance of OSPF? 

A. 90 

B. 100 

C. 110 

D. 120 

Correct Answer: C 

Administrative distance is the feature that routers use in order to select the best path when there are two or more

different routes to the same destination from two different routing protocols. Administrative distance defines the reliability

of a 

routing protocol. Each routing protocol is prioritized in order of most to least reliable (believable) with the help of an

administrative distance value. 

Default Distance Value Table 

This table lists the administrative distance default values of the protocols that Cisco supports: 

Route Source 

Default Distance Values 

Connected interface 

Static route 

Enhanced Interior Gateway Routing Protocol (EIGRP) summary route External Border Gateway Protocol (BGP) 

Internal EIGRP 

IGRP 

OSPF 

Intermediate System-to-Intermediate System (IS-IS) Routing Information Protocol (RIP) 

Exterior Gateway Protocol (EGP) 

On Demand Routing (ODR) 

External EIGRP 

Internal BGP 

Unknown* 

QUESTION 6

Which two fields are included in the TCP and UDP packet headers? (Choose two) 

A. destination port 

B. sequence number 

C. checksum 

D. offset 

E. window 

Correct Answer: AB 

QUESTION 7

What are two advantages of static routing? (Choose two) 

A. It cannot be used to load-balance traffic over multiple links 

B. It allows the network to respond immediately to changes 

C. It can be implemented easily even in large environments. 

D. It allows the administrator to control the path of traffic 

E. It produces minimal CPU load. 

Correct Answer: DE 

QUESTION 8

Which protocol can cause overload on a CPU of a managed device? 

A. Netflow 

B. WCCP 

C. IP SLA 

D. SNMP 

Correct Answer: D 

Sometimes, messages like this might appear in the router console: 

%SNMP-3-CPUHOG: Processing [chars] of [chars] 

They mean that the SNMP agent on the device has taken too much time to process a request. 

You can determine the cause of high CPU use in a router by using the output of the show process cpu command. 

Note: A managed device is a part of the network that requires some form of monitoring and management (routers,

 » Read more about: Get the latest Cisco CCNA 200-125 dumps and 200-125 pdf, pass exam certification  »